• Motor Nameplate and Ratings Explained

     · It is important to note that many of the other ratings found on the nameplate such as power factor, efficiency, torque and current only apply at rated voltage and frequency. Fullload current (FLA) As the connected load and required torque on an electric motor increases, the amperage required to power the motor also increases. The fullload current (FLA) is the maximum expected amperes .

    Get Price
  • power factor and efficiency of large crusher motors

    Crusher Duty Motors c power factor and efficiency values as a function of load. HV motors are supplied with a voltage rarely exceeding kV, their power ranges from 100 kW to over 10 MW, with an average of 800 kW. asynchronous cage motors These HV motors fall into two main egories according to their rotor composition which can be single or double cage.

    Get Price
  • Causes of Low Power Factor and it's Correction (PF ...

    Power Factor Correction. As discussed above, low power factor is mainly due to lagging currents drawn by inductive loads. Before we study the schemes for Power Factor Correction (PFC), note the following points: For pure inductance, current lags behind voltage by 90°. For pure capacitance, current leads voltage by 90°.

    Get Price
  • POWER FACTOR BENEFITS OF HIGH EFFICIENCY MOTORS

    power factor motor. However, many larger commercial, manufacturing and industrial facilities do have a power factor penalty, and for these facilities, the savings on power factor charges can help further improve the cost effectiveness of replacing a motor with the higher cost premium efficiency motor. Several examples are shown to demonstrate the additional cost savings .

    Get Price
  • Power factor

    Powerfactor correction increases the power factor of a load, improving efficiency for the distribution system to which it is attached. Linear loads with low power factor (such as induction motors) can be corrected with a passive network of capacitors or inductors. Nonlinear loads, such as rectifiers, distort the current drawn from the system. In such cases, active or passive power factor ...

    Get Price
  • Motor Sizing Principles

    1. Peak load torque (or power) < Rated Motor torque (or power) x (1+Service factor/) 2. The root mean square load torque (power) requirement must be less than of the rated motor torque (power) and ideally greater than 75% of rated motor torque (power). 3. Check that the Motor can start the load and get it up to speed.

    Get Price
  • Chapter : Energy Efficient Technologies in Electrical ...

    c) Automatic power factor controller d) KILOVAR 5. The following function can not be achieved with automatic power factor controllers. a) Voltage control b) KILOVAR control c) kW control d) PF control 6. The following features apply to energy efficient motors by design: a) Energy efficient motors last longer b) Starting torque for efficient ...

    Get Price
  • power factor and efficiency of large crusher motors

    Motor Efficiency Power Factor and Load EC M. Aug 15 2013 Proper electric motor appliion and efficiency are important things to load and can make the load on the generator larger than necessary. Get Price; Determining Electric Motor Load Factor P2 InfoHouse. M motors account for a large part of your monthly Most electric motors are designed to run at 50 to 100 percent of rated load ...

    Get Price
  • Power Factor Improvement

    The large current at low power factor causes more I2R losses in all the elements of the supply system. This results in poor efficiency. (iv) Poor voltage regulation. The large current at low lagging power factor causes greater voltage drops in alternators, transformers, transmission lines and distributors. This results in the decreased voltage available at the supply end, thus impairing the ...

    Get Price
  • PREMIUM EFFICIENCY MOTOR SELECTION AND APPLICATION .

    Service Factor ..... 66 Motor Speed, Slip, and Torque Relationships ... Motor power factor as a function of percent fullload amperage..... 413 Figure 51. Voltage variation effect on standard efficiency motor performance ..... 53 Figure 52. Motor derating due to voltage unbalance..... 54 Figure 53. Effects of voltage unbalance on motor losses..... 55 Figure 54. Sine wave overlaid on ...

    Get Price
  • Disadvantages of Low Power Factor

    Low Efficiency: In case of low Power Factor, there would be large voltage drop and large line losses and this will cause the system or equipment efficiency too low. For instance, due to low power factor, there would be large line losses; therefore, alternator needs high excitation, thus, generation efficiency as well as transformer's ...

    Get Price
  • Motor Starting Power Power Factor

     · Full load efficiency and power factor. Half load efficiency and power factor. ===== (2B)+(2B)' ? RE: Motor Starting Power Power Factor X49 (Electrical) (OP) 20 Aug 10 13:57. dpc, I'm not interested in what the starting current will be, since this only affects the generator windings and not the engine, which will be the limiting factor. It is the real power .

    Get Price
  • power factor and efficiency of large crusher motors

    Motor Efficiency Power Factor and Load EC M. Aug 15 2013 Proper electric motor appliion and efficiency are important things to load and can make the load on the generator larger than necessary. Get Price; Determining Electric Motor Load Factor P2 InfoHouse. M motors account for a large part of your monthly Most electric motors are designed to run at 50 to 100 .

    Get Price
  • Performance Efficiency

    For petrol and conventional electrical outboard motors the propulsive power is not normally revealed. Instead, less meaningful indiors are used, such as shaft power, input power or even static thrust. That wouldn't be so bad if the differences between the various power ratings were minimal. But they aren't; they're very large. The propulsive power of a petrol outboard with 4 HP shaft ...

    Get Price
  • Gears Gear Efficiency

    The efficiency of a gear system is simple calculated as the [output shaft power /Input shaft power ].100 %. The output power is the (input power the power losses). Power losses in gear systems are associated primarily with tooth friction and lubriion churning losses. Churning losses are relatively independent of the nature of the gears and the gear ratios they are primarily realated to ...

    Get Price
  • power factor and efficiency of large crusher motors

    Motor Efficiency and Power Factor. Electric power consumption is rated power divided by motor efficiency. Rated power depends on class of motor (which considers intended duty). Industrial grade motors usually are rated for continuous duty. Motor efficiency requirements are set by 1992 Energy Policy Act (EPACT), primarily for larger motors as used in industry and .

    Get Price
  • PREMIUM EFFICIENCY MOTOR SELECTION AND APPLICATION .

    Service Factor ..... 66 Motor Speed, Slip, and Torque Relationships ... Motor power factor as a function of percent fullload amperage..... 413 Figure 51. Voltage variation effect on standard efficiency motor performance ..... 53 Figure 52. Motor derating due to voltage unbalance..... 54 Figure 53. Effects of voltage unbalance on motor losses..... 55 Figure 54. Sine wave .

    Get Price
  • power factor and efficiency of large crusher motors

    power factor and efficiency of large crusher motors Description : Severe Duty Motors – BR420 – Baldor Crusher Duty . and efficient motor, built rugged enough ... Motor Efficiency, Selection and Management ... higher motor current, lower power factor and higher energy loss ... This is especially true for large motors, ... Motor Efficiency ...

    Get Price
  • power factor and efficiency of large crusher motors

    Motor Efficiency and Power Factor. Electric power consumption is rated power divided by motor efficiency. Rated power depends on class of motor (which considers intended duty). Industrial grade motors usually are rated for continuous duty. Motor efficiency requirements are set by 1992 Energy Policy Act (EPACT), primarily for larger motors as ...

    Get Price
  • How capacitors improve the power factor and how to ...

     · Based on the power of a receiver in kW, this table can be used to calculate the power of the capacitors to change from an initial power factor to a required power factor. It also gives the equivalence between cos ø and tg ø. Example: 200 kW motor – cosφ = – required cosφ = – Qc = 200 x = 98 kVAr.

    Get Price